(Vortech/Paxton) WhaleShark Bracekt Kit

The Adapt Lab “WhaleShark” bracket aims to bring what the market has been missing for a while: A quality complete bracket kit to mount a Vortech/Paxton supercharger on your UZ engine. While many other kits are more expensive, more prone to heat soak and produce hp numbers that are lacking, this kit brings more value in a better package. Bolting onto all UZ engines from 1UZ non-vvti to 3UZ vvti, there is no way you will be left out.

Designed from the ground up for the highest belt wrap possible. Beating any previous or current supercharger setup available for the UZ family of engines. This kit achieves 220-240 degrees of belt wrap. This drastically reduces the possibility of slip which is not attainable with any other kit. No point in going with a setup that is doomed from the beginning, so we built in hard adjustment points to allow moving an idler closer to the supercharger pulley as the pulley gets smaller in highest boost setups.

Even with the high strength stainless steel bracket being 7-8lbs, we still achieve a roughly 25-27 lb total weight with the bracket and the Vortech blower (Vortech V3 Si was used for the weight) making it the lightest supercharger kit offering ever.

We took care to precisely machine the spacers for the supercharger. With an accuracy of .05mm we guarantee proper alignment with the rest of the drive system on the engine. This level of accuracy allows the idlers to be put closer to the supercharger pulley without causing weird loading that can cause the belt to come off.

Superchargers love longer runner lengths. This tends to be a point that does not get talked about enough. While many see longer runners better for low end power hurting peak performance, this is a benefit when paired to supercharged engines. Why bring this up? The UZ family of engines has historically long runners on the intake manifold so an intake manifold change most likely is not necessary to reach your power goals when you choose a centrifugal supercharger. This allows you to spend money elsewhere where it is needed. If a top mount supercharger is used with an aftermarket intake manifold utilizing very short runners (typically under 3 inches) this will reduce overall power, force you to run more boost creating excess heat and most of these setups with the positive displacement blowers will not net over 400whp even with over 10 psi of boost.

Positive displacement blowers also mount directly on top of the engine soaking up large amounts of heat while creating heat from the compression of the air. With a Vortech blower the heat from the engine will not transfer into the head unit reducing heat soak. Less heat soak means lower intake air temperature for more efficient power.

No compromises in performance are required when choosing this kit and the mounting is the simplest as well. All of the magic happens on the front of the engine so no need to remove the intake manifold or mess with the fuel system either. It will require that you swap over to the proper fan clutch bracket (LS400 engines should already have this) but most engines already have the correct bracket from factory. The goal for this install is to get you from start to finish and driving in 48 hours. No cutting, welding or modifying the front water bridge required.

No compromises in comfort either. This kit is A/C friendly. All the components were made with A/C in mind. If you are not running A/C all of the components will be provided for a non A/C setup.

This is the best kit for supercharging your UZ engine. Long gone are the days of 20 year old blowers mounted on top of your engine. With a wide range of mountable blowers you can easily find the right blower to support your power goals. No need to break the bank either as this is the most cost effective form of boost beating even budget turbo setups. Light weight, no heat soak, high belt wrap, easy install, well priced, built with high quality components and precision makes the Adapt Lab solution the right solution.

• Fits non-vvti 1UZ, 2UZ, and vvti 1UZ, 2UZ, 3UZ engines
• ***This kit is to be used in the Lexus 89-00 LS400. Battery relocation is required. Electric fan conversion is highly recommended. While the fan clutch assembly will not interfere with the blower the factory fan shroud on a Ls400 will not allow the blower to be installed. We recommend low profile electric fans that flow at a minimum of 3500cfm combined. ***
•  This bracket supports the following Vortech model superchargers: V1, V2, V3, V4, V7. MUST BE A COUNTERCLOCKWISE UNIT (CCW) this will not work with CW rotation blowers.
•  This bracket supports the following Paxton model superchargers: Novi 1200, Novi 1200SL, Novi 1220, Novi 1220SL, Novi 1500, Novi 1500SL, Novi 2200,
  Novi 2200SL, Novi 2200X. MUST BE A COUNTERCLOCKWISE UNIT (CCW) this will not work with CW rotation blowers.
• This kit includes the supercharger bracket, bracket spacers, blower spacers, studs, washers, nuts, pulleys, idlers and bolts.
• Belt wrap will range between 220-240 degrees depending on pulley size and idler position (idler position matrix will be provided for best wrap on specific pulleys).
• Requires the use of the fan clutch bracket. This supercharger kit will NOT bolt on with the hydraulic pump bracket found on some 1UZ engines. ***WE DO HAVE a drop down menu where you can purchase the necessary fan bracket and pulley required to bolt on this supercharger kit. Drop down menu can be found back at the top of the page.***
•  This kit supports usage with an A/C compressor or without it.
•  This kit is designed to be used with a 6-rib supercharger drive pulley. It can be used with an eight rib or ten rib pulleys but only in the smallest size (2.5-2.6
  inch). There are some in-between sizes that may suit your boost target better, but we advise staying with the 6 rib pulleys (https://vortechsuperchargers.com/products/copy-of-s-c-pulley-6- rib srsltid=AfmBOooHQJ6wmta8PHabQ4e2ceVtW-uFNKYsYS3lbRbr0FHgmUZH1z9x)
• For the individuals running stock distributors, there is an additional bracket that can be purchased to properly hold the ignition coil since that bracket will have to be eliminated. We have a bracket for the MSD ignition coil #8226 which is a part of our kit for non vvti 1UZ engines and the Oem ignition coil as well. This can be found in a drop down menu at the top of the page.
• The provided spacers MUST BE USED as instructed or you risk tossing the belt off and causing damage. The supplied Dorman idler pulleys MUST BE USED as well. These idlers were specifically selected as a control variable for belt alignment.
• The supercharger pulley must be setup to where the ribs are closest to the blower. Incorrectly mounting the pulley will mean the ribs will not match the
  alignment of the engine when using the supercharger spacers.
• SERPENTINE BELT SIZE: Belt size for this kit is ranging between 108-112 inches with the use of 2.87″-3.8″ pulleys (interpolate belt size if you are not using these pulley sizes). It is a good idea that you consider changing belt size to always have the shortest belt possible. The less belt there is the less belt there isto stretch.
• To get more tension on the serpentine belt system please modify the factory tensioner. This will allow you to also run a shorter belt. A shorter belt means less belt to stretch. Watch this video to learn how to modify you tensioner. (https://youtu.be/Gp335z5QN4g?si=nZ8RCwntemTi5sWR)